ARTM嵌入式PT100傳感器無線測溫智能溫度巡檢儀適用于一路或多路溫度的測量和控制，主要應用于火電廠、水電站等場合的溫度巡檢測量及控制。ARTM-8 嵌入式PT100傳感器無線測溫智能溫度巡檢儀適用于多路溫度測量與控制，可接入最多8路PT100 傳感器，適用于低壓開關柜電氣接點、變壓器繞組、電機繞組等場合的測溫

1，型號與功能

注：ARTM8的測溫通道可由用戶，具體見訂貨范例。

2，技術參數

1.4 包裝

1.4 Packaging

包裝內含下列項目：

Packaging contains the following items:

主機（含插拔式端子排，銘牌，安裝支架等）；

Main engine (including plug-in terminal, nameplate, mounting bracket, etc.)

產品安裝使用手冊。’

Product installation manual.

在打開產品包裝時，請仔細檢查是否有損壞，如有任何損壞，請及時通知ACREL公司或代理商，并請保留損壞的外包裝。如系ACREL公司或代理商責任，將及時予以更換。

When opening the product packaging, please check if there is any damage, please inform ACREL or agent in time, and please keep the damaged outer packing. If it is the responsibility of ACREL company or agent, it will be replaced in time.

1.5 安裝和接線方法

1.5 Installation and fixing

1.5.1 安裝尺寸

1.5.1 Outlines

n ARTM8：

1.5.2安裝方法

1.5.2 Installation

在您的配電盤上，選擇合適的地方開一個與所安裝溫度巡檢儀開孔尺寸相同的安裝孔。

On your switchboard, select the appropriate place to open a hole with the same size as the installed temperature inspector.

取出溫度巡檢儀，松開定位螺釘（逆時針），取下安裝支架。

Remove the temperature inspector, loosen the positioning screw (counterclockwise) and remove the mounting bracket.

把儀表插入配電盤儀表孔中。

Insert the meter into the dial gauge hole.

插入儀表后裝上安裝支架、定位螺釘（順時針）。

Insert mounting bracket and positioning screw (clockwise) after instrumentation.

1.5.3 接線方法（請以儀表上的接線圖為準）

1.5.3 Fixing (Please refer to the wiring diagram on the meter)

n ARTM8：

注意：二線制接線時必須按照圖示，將熱電阻傳感器的其中一根引線接到2個端子上。

Notice：In the second wire connection, one of the wires of the thermal resistance sensor must be connected to two terminals according to the diagram.

2 操作指南

2.1 顯示介紹

2.1 Display explanation

n ARTM8的面板圖示

n ARTM8 Panel graphic

2.2 系統上電

2.2 System power on

依照說明正確接線后，接通工作電源即進入測量狀態。

After the correct wiring is indicated, the working power is connected to the measuring state.

2.3 系統設置模式

2.3 System setting mode

2.3.1 進入/退出系統設置模式

2.3.1 Enter/exit system setting mode

在正常情況下，儀表處于正常工作狀態，此時按下SET鍵大于3秒，會進入系統設置模式，進入系統設置模式前，首先需要輸入正確的密碼（出廠時一般設置為0001）。

Under normal circumstances, the normal work of the instrument, press the SET key at this time more than 3 seconds, will enter the system setup mode, before entering the system setup mode, you first need to enter the correct password (factory generally SET to 0001).

進入系統設置模式的具體操作如下：

The specific operation of entering the system setting mode is as follows:

（1）按住SET鍵，直至畫面顯示“Prog"，再單擊回車鍵，顯示“code"，提示要輸入密碼，再單擊回車鍵出現“0000"，按左右方向鍵減小或增大數值大小至正確的密碼；

（1）Press SET key, until it showed "Prog", then click the enter key to display "code", prompt to enter a password, then click the enter key in "0000", according to the or so direction key numerical size to decrease or increase the correct password.

（2）密碼正確，則畫面顯示“PASS"，單擊回車即進入系統設置的最高一層菜單；否則顯示“Err"（error），單擊回車返回正常模式。

（2）The password is correct, the screen shows "PASS", and click enter to enter the highest level menu of system Settings; otherwise, "Err" (error) is displayed, and click return to return to normal mode.

系統設置包括報警點設置（菜單“SET"），回滯量及報警延時設置（菜單“HyS"），顯示模式設置（菜單“DISP"），通訊設置（菜單“BUS"），設置新密碼（菜單“n.cod"），查看軟件版本號（菜單“UErn"）。

System Settings includes emergency alarm Settings (menu "SET"), the amount of hysteresis and alarm delay Settings

(menu " HyS "), the display mode Settings (menu " DISP "), communication Settings (menu "BUS"), setting a new password (menu "n.cod"), to check the software version number (menu "UErn").

2.3.2 系統設置模式下的操作

2.3.2 Operation under system setting mode.

進入系統設置模式后，選擇菜單狀態進入。

After entering the system Settings mode, select menu status to enter.

（1）“SET"狀態設置

（1）“SET" state setting

密碼設置成功，進入系統設置模式以后，按左或右方向鍵直到顯示“SET"，回車確認后顯示“CH1"，再次回車后顯示“ON"或“OFF"，可按左或右方向鍵選擇。選擇“OFF"，回車，即屏蔽通道1的溫度測量和監控，畫面返回“CH1"；選擇“ON"，回車，即打開通道1的溫度測量和監控，并顯示“AL1"，即通道1的報警點1的設定，回車進入顯示“HI"或“LO"，首先按左或右鍵選擇設定報警點1的報警趨勢，“HI"表示高越限報警，“LO"表示低越限報警，回車確認后設定具體數值，按左右方向鍵減小或增大數值大小，達到要求后回車確定，系統返回“AL1"。

After entering the system setting mode, press left or right arrow keys until the "SET" is displayed. After returning the car, the "CH1" will be displayed, and the "ON" or "OFF" will be displayed after enter, and the left or right arrow keys can be selected. Select "OFF", enter, the temperature measurement and monitoring of shield channel 1, and return "CH1"; Choose "ON", press enter, or open channel 1 temperature measurement and monitoring, and display the "AL1", namely channel 1 emergency alarm 1 set, enter into the show "HI" or "LO", firstly, according to the left or the right to choose to set alarm trend of emergency alarm 1, said "HI" the high limit alarm, "LO" said low limit alarm, press enter to confirm after setting specific values, press the left right direction key numerical size, decrease or increase after reaching requirements determine rate of return, return to "AL1" system.

在“AL1"狀態下按左或右鍵選擇“AL2"，即通道1的報警點2的設定，設定方法與“AL1"*相同。

In the "AL1" state, press left or right select "AL2", which is the setting of alarm point 2 of channel 1, and the setting method is exactly the same as "AL1".

在“AL1"或“AL2"狀態下，按“SET"鍵返回“CH1"，此時再按左或右鍵選擇可進入其他通道的設置，設置方法與通道1*相同。

Under the condition of "AL1" or "AL2", press "SET" to return "CH1". At this time, select the Settings that can enter other channels on the left or right button, and the setting method is exactly the same as channel 1.

在“CH1"、“CH2"、“CH3"等狀態下按“SET"鍵返回最高一層菜單“SET"。

Press "SET "to return the top menu "SET" in "CH1", "CH2" and "CH3".

（2）“HyS"狀態設置

（2）“HyS" state setting

進入系統設置模式以后，按左或右方向鍵直到顯示“HyS"，即設置報警的回滯量和報警延時。按回車鍵進入,選擇“HyS1"設定所有通道報警1的回滯量；選擇“HyS2"設定所有通道報警2的回滯量，選擇“DEL"設定報警延時時間。報警延時設定的范圍是1～10，而單位并非秒，假定現設定報警延時值為4，即連續“4"次測得某一通道的溫度處于報警位置，才觸發報警。

After entering the system setting mode, press the left or right arrow keys until the "HyS" is displayed, that is, set the alarm back delay and alarm delay. Press enter key to enter, select "HyS1" to set the return amount of all channel alarm 1; select "HyS2" to set the back delay of all channel alarm 2, and select "DEL" to set alarm delay time. The range of alarm delay setting is 1~10, and the unit is not seconds, assuming that the alarm delay value is 4, that is, the temperature of a channel must be set at the alarm setting in a continuous "4" test, then the alarm will be triggered.

（3）“DISP"狀態設置

（3）“DISP" state setting

進入系統設置模式以后，按左或右方向鍵直到顯示“DISP"，按回車鍵進入“cyc"狀態，即設置循環顯示各通道溫度值的間隔時間，回車進入數值設置，設置范圍0～20，其中0表示正常模式下靜態顯示某一通道的溫度值，其余數值即正常模式下循環顯示的間隔時間（單位：秒）?；剀嚧_認后返回“DISP"狀態。

Into system setting mode, press left or right direction until the show "DISP", press the enter key to enter "cyc" state, which set up the cycle time interval of each channel temperature value, enter into the value set, the set range 0 ~ 20, where 0 means normal mode shows a static channel temperature value, the rest of the numerical display of cycle in the normal mode namely time interval (unit: second). Enter the "DISP" state after the enter confirmation.

設定靜態顯示，在正常模式下按住左或右鍵不放，可快速切換到需要的通道溫度顯示，并保持。

Set the static display, press left or right button in normal mode, can accelerate the switch to the required channel temperature display, and maintain.

設定循環顯示，在正常模式下按住右鍵不放，可加快循環顯示速度。

Set the cycle to display, under normal mode, hold right button, can speed up the circulation display speed.

（4）“BUS"狀態設置

（4）“BUS" state setting

進入系統設置模式以后，按左或右方向鍵直到顯示“BUS"，即通訊設定，回車確認后顯示“Addr"狀態，再次回車后就可以設置地址的值，通過左或右方向鍵改變地址值，按回車確認后返回“Addr"狀態，按左或右方向鍵選擇“Baud"狀態，回車進入后通過左或右方向鍵選擇合適的波特率，按回車鍵確認退出。

Enter the system after setting mode, press left or right direction until the show "Bus", namely the communication setting, press enter to confirm after the "Addr" status display, enter again after can set the value of address, change address

values by left or right direction key, press enter to confirm back the "Addr" status, according to the left or right direction key to choose "Baud" state, after enter into by left or right direction key to choose the appropriate Baud rate, press enter to confirm.

（5）“n.cod"狀態設置

（5）“n.cod" state setting

進入系統設置模式以后，按左或右方向鍵直到顯示“n.cod"，即設置新的系統密碼，按回車進入后，按左或右鍵輸入合適的新密碼后，按回車確認。

Enter the system after setting mode, press left or right direction until the show "n.cod", set up new system password, press enter to enter, press the left or right input right after the new password, and press enter to confirm.

（6）“UErn"狀態設置

（6）“UErn" state setting

進入系統設置模式以后，按左或右方向鍵直到顯示“UErn"，即查看產品軟件版本號，按回車后進入查看狀態。

After entering the system setting mode, press the left or right arrow keys until the "UErn" is displayed, that is, check the product software version number, and press enter to enter the viewing status.

2.3.3 保存設置選擇

2.3.3 Save Settings selection

全部參數設置完成后，在上述六個狀態中的任意一個狀態下按“SET"鍵，進入“SAUE"狀態，即保存數據。此時，按回車鍵保存設置的內容，按“SET"鍵直接退出系統設置模式，不保存所設置的內容，返回正常模式后按原有參數運行。

After all the parameter Settings are completed, press the "SET" button in any of the above six states to enter the "SAVE" state, which is to save the data. At this time, press enter key to save the Settings, press the "SET" key to directly exit the system setting mode, do not save the contents SET, return to normal mode and follow the original parameters.

2.3.4 用戶編程流程圖

2.3.4 The Programming chart

3通訊指南

3 Communication

在本章主要講述如何利用軟件通過通訊口來操控該系列儀表。本章內容的掌握需要您具有MODBUS協議的知識儲備并且通讀了本冊其他章節所有內容，對本產品功能和應用概念有較全面的了解。

This chapter focuses on how to use software to manipulate the series of instruments through a communication port. The mastery of the content of this chapter requires that you have the knowledge reserve of MODBUS protocol and read all the contents of the other chapters of this book, and have a comprehensive understanding of the functions and application concepts of the product.

本章內容包括：MODBUS協議簡述，通訊應用格式詳解，本機的應用細節及參量地址表。

The contents of this chapter include: brief introduction of MODBUS protocol, details of communication application format, application details of the machine and parameter address table.

3.1 協議簡述

3.1 The protocol explanation

3.1.1 傳輸方式

3.1.1 Transmission format

傳輸方式是指一個數據幀內，一系列獨立的數據結構以及用于傳輸?shù)臄?shù)據的有限規則，下面定義了與MODBUS協議（RTU方式）相兼容的傳輸方式。

Transport refers to a data frame, a series of separate data structure and used for the transmission of data to limited rules, the following defines that is compatible with the MODBUS protocol (RTU) transmission mode.

每個字節的位

Bits per byte

l 1個起始位

l 1 start bit

l 8個數據位，最小的有效位先發送

l 8 data bits, the smallest valid bit is sent firstly

l 無奇偶校驗位

l Unexciting parity bit

l 1個停止位

l 1 stop bit

錯誤檢測：CRC（循環冗余校驗）

Error detection: CRC (Cyclic redundancy check)

3.1.2 協議

3.1.2 Protocol

當數據幀到達終端設備時，它通過一個簡單的“端口"進入被尋址的設備，該設備去掉數據幀的“信封"（數據頭），讀取數據，如果沒有錯誤，就執行數據所請求的任務，然后，它將自己生成的數據加入到取得的“信封"中，把數據幀返回給發送者。返回的響應數據幀中包含了以下內容：終端從機地址（Address）、被執行了的命令（Function）、執行命令生成的被請求數據（Data）和一個校驗碼（Check）。發生任何錯誤都不會有成功的響應。

When data frames to terminal equipment, it by a simple "ports" to be addressing device, the device to remove the "envelope" data frames (data), read the data, if there are no mistakes, will carry out the tasks of the requested data, then, it will generate its own data to join the "envelope" of the data frame is returned to the sender. The response returned Data frame contains the following contents: the terminal Address (Address), was carried out from the machine's command (Function), execute the command to generate the requested Data (Data) and a Check code (Check). There will be no successful response to any errors.

3.1.2.1 數據幀格式

3.1.2.1 Data frame format

3.1.2.2地址域

3.1.2.2 Address code

地址域在幀的開始部分，由一個字節（8位二進制碼）組成，十進制為0～255，在我們的系統中只留用1～247，其它地址保留。這些位標明了用戶的終端設備地址，該設備將接收來自與之相連的主機數據。每個終端設備的地址必須是的，僅僅被尋址到的終端會響應包含了該地址的查詢。當終端發送回一個響應，響應中的從機地址數據便告訴了主機哪臺終端正與之進行通訊。

The Address is at head of the data, and it has 1 byte (8-bits binary code). The decimal is 0~255. In ARTM, it just uses 1~247. It stores the slave address. These bits indicate the address of the terminal device specified by the user, which will receive the host data that is connected to it. The address of each terminal device must be only one, and only the addressable terminal will respond to the query containing the address. When the terminal sends back a response, the data from the machine address in the response tells the host which terminal is communicating with it.

3.1.2.3 功能域

3.1.2.3 Function code

功能域代碼告訴了被尋址到的終端執行何種功能。下表列出了該系列儀表用到的功能碼，以及它們的意義和功能。

The functional domain code tells what function the addressable terminal performs. The following table lists the functional codes used in this series of instruments, as well as their meanings and functions.

3.1.2.4 數據域

3.1.2.4 Data code

數據域包括了終端執行特定功能所需要的數據或者終端響應查詢時采集到的數據。這些數據的內容可能是數值、參考地址或者設置值。例如：功能域碼告訴終端讀取一個寄存器，數據域則要指明從哪個寄存器開始及讀取多少個數據，內嵌的地址和數據依照類型和從機之間的不同內容而有所不同。

The data domain includes the data that the terminal needs to perform a particular function, or the data collected when the terminal responds to the query. The contents of these data may be numeric, reference addresses, or set values. For example, code tells terminal functional domains to read from a register, data domain to indicate the starting which register and read how many data, the embedded address and data in accordance with the type and different content varies between machine.

3.1.2.5 錯誤校驗域

3.1.2.5 Check code

該域允許主機和終端檢查傳輸過程中的錯誤。有時，由于電噪聲和其它干擾，一組數據在從一個設備傳輸?shù)搅硪粋€(gè)設備時在線路上可能會發生一些改變，出錯校驗?zāi)軌虮ＷC主機或者終端不去響應那些傳輸過程中發生了改變的數據，這就提高了系統的安全性和效率，錯誤校驗使用了16位循環冗余的方法。

This code allows the error of transmission between the master and slave. Sometimes, there will be the errors when a data transferred from equipment to another in the interference due to the electrical noise and other disturbances. The check code can make the slave not to answer the error data in the transmission. This improves the security and efficiency of the system. Check node uses 16-bits cyclic redundancy.

3.1.3錯誤檢測的方法

3.1.3 Check mode

錯誤校驗（CRC）域占用兩個字節，包含了一個16位的二進制值。CRC值有傳輸設備計算出來，然后附加到數據幀上，接收設備在接收數據時重新計算CRC值，然后與就收到的CRC域中的值進行比較，如果這兩個值不相等，就發生了錯誤。

CRC occupies 2 bytes, and it contains a binary value of 16 bits. It is got by the transmission equipment, and than it is added in the data frame. The master will recalculate the CRC value, and then it compares the value to that received. If 2 values is not same, there must be error.

CRC運算時，首先將一個16位的寄存器預置為全1，然后連續把數據幀中的每個字節中的8位與該寄存器的當前值進行運算，僅僅每個字節的8個數據位參與生成CRC，起始位和終止位以及可能使用的奇偶位都不影響CRC。在生成CRC時，每個字節的8位與寄存器中的內容進行異或，然后將結果向低位移位，高位則用0補充，位（LSB）移出并檢測，如果是1，該寄存器就與一個預設的固定值（0A001H）進行一次異或運算，如果位為0，則不作任何處理。

The CRC algorithm, you will preset a 16-bit register all to 1, then each byte in the data frame of eight consecutive operation with the current value of the register, only 8 bits of each byte in generate CRC, start bit and stop bit and the possibility of using parity bit does not affect the CRC. When generate CRC, each byte of eight different XOR with the contents of the registers, then the results to the low displacement, high use 0, lowest (LSB) removed and test, if it is 1, the register is fixed with a preset value (0A001H) for an XOR operation, if the lowest is 0, do not make any processing.

上述處理重復進行，直到執行完了8次移位操作，當最后一位（第8位）移位完成以后，下一個8位字節與寄存器的當前值進行異或運算，同樣進行上述的另一個8次移位異或操作，當數據幀中的所有字節都作了處理，生成的最終值就是CRC值。

The above process repeated, until the end of the eight times perform shift operation, when the last one (eighth) after the completion of the shift, an 8-bit bytes and register under the current value of XOR operation, another eight times for the same shift XOR operation, when all the bytes of a data frame processing, generate the final value is CRC value.

生成一個CRC的流程為：

The process of generating a CRC is:

1、 預置一個16位寄存器為0FFFFH（全1），稱之為CRC寄存器。

1、 Preset a 16-bit register to be 0FFFFH (all 1), which is called CRC register.

2、 把數據幀的第一個字節的8位與CRC寄存器中的低字節進行異或運算，結果存回CRC寄存器。

2、XORing the 8 bits of the first byte of the data frame with the low byte in the CRC register, and the result is saved back to the CRC register.

1、 將CRC寄存器向右移一位，最高位填以0，位移出并檢測。

3、Move the CRC register to the right one, the highest position is 0, and the minimum displacement is detected.

4、如果位為0：重復第三步（下一次移位）；如果位為1：將CRC寄存器與一個預設的固定值（0A001H）進行異或運算。

4、If the lowest level is 0: repeat step 3 (the next shift);If the lowest level is 1: the CRC register is XORed with a preset fixed value (0A001H).

5、 重復第三步和第四步直到8次移位。這樣處理完了一個完整的8位。

5、Repeat step 3 and step 4 up to 8 shifts. This completes a complete 8 bit.

6、 重復第2步到第5步來處理下一個8位，直到所有的字節處理結束。

6、Repeat step 2 to step 5 to handle the next 8 bit, knowing that all byte processing ends.

7、 最終CRC寄存器的值就是CRC的值。

7、The value of the final CRC register is the value of CRC.

此外，還有一種利用預設的表格計算CRC的方法，它的主要特點是計算速度快，但是表格需要較大的存儲空間，該方法此處不再贅述，請參閱相關資料。

In addition, there is a way to use the default form of CRC calculation method, its main characteristic is computing speed, but the form needs large storage space, the method is no longer here, please refer to the relevant information.

3.2 通訊應用格式詳解

3.2 Communication example

本節所舉實例將盡可能的使用如下表所示的格式，（數字為16進制）。

The examples in this section will use the format shown in the following table as much as possible (the number is hexadecimal).

Addr：從機地址

Addr: slave address

Fun：功能碼

Fun: function code

Data start reg hi：數據起始地址 寄存器高字節

Data start reg hi: the start of data code, the high byte

Data start reg lo：數據起始地址 寄存器低字節

Data start reg lo: the start of data code, the low byte

Data #of reg hi：數據讀取個數 寄存器高字節

Data #of reg hi: the number of data, the high byte

Data #of reg lo：數據讀取個數 寄存器低字節

Data #of reg lo: the number of data, the low byte

CRC16 hi：循環冗余校驗 高字節

CRC16 hi: check data, the high byte

CRC16 lo：循環冗余校驗 低字節

CRC16 lo: check data, the low byte

3.2.1 讀數據（功能碼03/04）

3.2.1 Read data (function code 03/04)

l 查詢數據幀

l The read data frame

此功能允許用戶獲得設備采集與記錄的數據及系統參數。主機一次請求的數據個數沒有限制，但不能超出定義的地址范圍。

This function allows the user to get the data measured and registered by slave and its system parameters. There is not the asking limit, but the data cannot exceed the defined code domain.

下面的例子是從01號從機讀3個采集到的基本數據（數據幀中的每個地址占用2個字節）T1、T2、T3，其中T1的地址為0006H，T2的地址為0007H，T3的地址為0008H。

For example, the 3 data (T1, T2, T3) is red by slave No.01. Each code in the data frame has 2 bytes. T1 is 0006H, T2 is 0007H, T3 is 0008H.

l 響應數據幀

l The answer data frame

響應數據幀包括從機地址、功能碼、數據的數量、采集的數據和CRC錯誤校驗。

The answer data frame includes slave address code, function code, data number code, the measured data code and CRC

code.

下面的例子是讀取T1、T2、T3（T1=016AH，T2=016BH，T3=0169H）的響應。

The example as below: T1, T2, T3（T1=016AH, T2=016BH, T3=0169H）

3.2.2 預置多寄存器（功能碼16）

3.2.2 Multi register (function code 16)

l 查詢數據幀

l The read data frame

功能碼16允許用戶改變多個寄存器的內容，該儀表中系統參數等可用此功能碼寫入。

The function code 16 allows user to change the content in the register. The system parameters of ARTM can be changed by this code.

下面的例子是預置ARTM8或ARTM16，設定溫度顯示的間隔時間為4秒，并關閉通道1和通道2的溫度測量。顯示控制字的地址為0003H，通道開/關狀態控制寄存器的地址為0004H。

The example as below, set the interval of loop display is 4 seconds; and turn off temperature input channel 1 and channel 2. The code of display control word is 0003H, the code of state of NO/OFF is 0004H.

l 響應數據幀

l The answer data frame

對于預置寄存器請求的正常響應數是在寄存器值改變后回應機器地址、功能碼、數據起始地址、數據個數、CRC校驗碼。

The normal response number for the preset register request is to respond to the machine address, function code, data start address, data number and CRC check code after the register value changes.

3.3 參量地址表

3.3 Parameter list

安科瑞電氣股份有限公司（代碼：300286）成立于2003年，集研發、生產、銷售及服務于一體，是一家為企業微電網提供能效管理和用電解決方案的高科技股份制企業。

??安科瑞電氣提供的解決方案包括變電所運維云平臺、安全用電管理云平臺、環保用電監管云平臺、智慧消防云平臺、能源管理云平臺、工業企業能源管控平臺、遠程預付費云平臺、餐飲油煙監管云平臺、電動汽車/電瓶車充電樁收費管理云平臺、電力監控/無線測溫系統、電能質量治理系統、電氣火災監控系統、消防設備電源監控系統、防火門監控系統、應急照明和疏散指示系統、智能照明控制系統、隔離電源絕緣監測系統等，幫助用戶實現能源智能化、可視化、精細化管理，提高用能效率和用能安全，為企業節能降耗和實現能源數字化建設提供數據服務。

??安科瑞電氣股份有限公司具備從云平臺軟件到終端元器件的產品生態體系，目前已有一萬多套系統解決方案運行在全國各地，為用戶高效和安全用能保駕護航。坐落于無錫江陰市的生產基地--江蘇安科瑞電器制造有限公司采用無鉛生產工藝，擁有功能完善的產品試驗中心，配合信息化管理系統，為公司產品產業化、規?；瘜?shí)施提供了保障。同時公司在全國主要城市配置銷售、技術支持團隊，快速響應客戶需求，為用戶提供良好的服務體驗。

??

??經過多年積累，公司參與了諸多能效管理項目，包括第七屆世界軍人運動會主會場電能質量治理、波音飛機完工及交付中心電力監控系統、嘉定區學校變電所運維云平臺、天水體育中心應急照明和疏散指示系統、杭州大江東寶龍廣場預付費云平臺、滬昆高鐵曲靖北站、嵩明站、富源北站等站房電力監控和智能照明控制系統、揚州大學廣陵校區宿舍用電管理系統等等；國外市場包括非洲、中東、東南亞、南美等等，豐富的市場經驗提升了公司的品牌影響力，在產品質量和服務方面贏得了廣泛的贊譽。

??公司自2012年上市以來一直保持穩定增長，公司將秉著“創新、高效、團結、誠信"的理念，堅持穩健經營、持續創新，為用戶提供更多更好的解決方案、產品和服務，為社會可持續發展貢獻力量。